Name: Evaporator
Brand: Friterm
Availability: InStock

New Water Drainage System

With the sloped water drain pan, drain water can be drained away easily and quickly. (For fan diameter ≥ 400 mm)

Thermally- Decoupled Double Layer Drip Tray

Thermally- decoupled drip tray prevents condensation at outside of the tray

Hinged Side Cover and Drip Tray

The hinged side covers and drip trays make it easier to access the coil and electrical connections.

Supports for Standing and Temporary Supports For Safe Transportation of the Unit

With the new design of lifting eyes and supporting legs it is easy to handle the units safely and easy to mount it to the ceiling in transport position. (There is no supporting legs for the units with Ø300-350 mm fans)

Removable Sections for inlet/outlet pipe connections.

With the special easy removable section design for headers, inlet/outlet connections can be done through top or sides of cover sheets.

Improved Pipe and Fin Structure for High Thermal Efficiency

Inner Grooved Copper pipes provides enhanced heat transfer coefficient in two-phase flow of refrigerant. Higher heat transfer peforamce on the air side is provided by the use of specially corrugated fins.

INSTALLATION AND MAINTENANCE, SET-UP, CARRYING AND LIFTING

• The units are packaged according to their dimensions and weight.

• Please read “Installation, Operation and Maintenance Instructions” for mounting and maintenance.

FEATURES AND APPLICATIONS

• FES model ceiling type unit coolers are specially designed for small, medium, and large industrial cold rooms, frozen storage, blast freezing, and rapid cooling room applications.

• Friterm FES series are ceiling mounted; single side discharge evaporators draw air across the coil.

• Unit coolers with three-phase motors are available for an operation with two rotation speed, and high speed provides a rapid pre-cooling and then slower air circulation, which avoids humidity loss.

• Friterm FES series consists of 606 models with a wide variety of accessories incorporates capacity range from 0,8 kW to 204 kW

• Units are suitable to work with refrigerants like R404A, R507, R134A, ...

• Capacities are given for R404A in the following pages

Coil Block

• Inline alignment that reduces defrost duration and defrost energy consumption,

• 4-7- 10- 12 mm fin pitches,

• Internally grooved copper tubes especially for air coolers, aluminum fins,

• Copper Inlet and outlet connections,

• Standart refrigerant connections are positioned on the right-hand side of the direction of the airflow.

• Refrigerant distributor,

• Optimized circuitry design,

• Test Pressure: 34 bar (PED 2014/68/EU)

• Maximum operating pressure: 22 bar

CASING

• Casing material is AlMg3 or galvanised steel depending on model and dimensions.

• All products are electrostatically powder-coated with RAL 9016, providing high corrosion resistance, smooth surface, and decorative appearance.

• Hinged side covers and drip tray for easy access.

• Special lifting eyes and supporting legs make transportation and installation easier (small air coolers with Ø300- 350 mm are delivered without supporting legs)

Drip Tray

• Dismountable drip tray for air coolers with Ø630- 800 mm fan,

• Hinged drip tray for air coolers with Ø300- 350- 400- 450- 500 mm fan,

• Thermally decoupled tray, which prevents the formation of condensation at the outside surface.

FANS

• High efficient axial Ziehl Abegg, EBM, or equivalent fans are employed in unit coolers with diameters of 300-350-400-450-500-630-800 mm.

• Motor protection classes are IP44 (for Ø400- 350- 300 mm) and IP54 (for Ø800- 630- 500- 450 mm); fans insulation classes are B and F.

• Minimum working temperatures are -25°C for monophase fans and -40°C for 3phase fans.

• Special fans should be used at the operating conditions below -40°C.

• Fans are arranged for standard draw through air configuration.

• Power data for 300/350/400/450 mm fans is 230V 1~50/ 60 Hz; for 500/630/800 mm fans is 400V 3~50 Hz,

• Three-phase AC fans can work at two different speeds.

• Thermistor connections must be done for motor protection in all fans where available.

• Friterm reserves the right to use fans of different manufacturers. Depending on the brand and type, the fan data may slightly vary

SOUND DATA

• Indicated sound pressure levels comply with EN 13487.

• Sound levels are obtained from sound power level (LwA) data provided by the fan manufacturers.

• For critical sound requirements, assistance and consultancy should be demanded from an expert.

ACCESSORIES

• Electrical defrost in coil block

• Electrical defrost in the drip tray

• Wiring of the fan on conjoint terminal box

• Brackets for wall-mounting

• Fan ring heaters

• Drainage heater

• Air streamers

• Connection for air distribution sock

• Textile hose, defrost flap

• Repair switches for fans

OPTIONS AND VARIANTS

• Air defrost

• Water defrost (for air coolers with Ø400- 450- 500- 630- 800 mm fan)

• Hot gas defrost (in coil and tray)

• Hot glycol defrost

• Coated fins

• Coated coil block

• AISI 304 or AISI 316 stainless steel casing

• Speed controllers

• Other fin pitch options

• 60 Hz motors

• EC fans

• Stainless steel tubes (AISI 304, AISI 316)

• Insulated drip tray

• Fan hood

• Blow-Through configuration system

• Installed expansion valve

• Reinforced fans

Friterm

FRITERM A.S. was founded in Istanbul in 1979. The company has developed its know-how and expertise by providing design, manufacturing, contract and sales services in Commercial Cooling, Industrial Cooling and Air Conditioning.

In time, Friterm has preferred to specialize on finned type heat exchangers and focused on the production of Air Cooled Condensers, Evaporators, Air Coolers, Dry Coolers, Water/Glycol Air Heaters and Coolers, Steam Heaters, Oil Coolers and Heat Recovery Coils for the Air Conditioning and Refrigeration Industry.

The company has included the energy sector in its fields of activity at the beginning of 2000s and expanded its product range. It has been designing and producing LT/HT Radiators, Combustion Turbine Inlet Air Cooling and Heating Units, Oil Coolers, Air Cooled ORC Condensers and Steam Condensers for the sector through its customized software.

CO2 Gas Coolers and Unit Coolers were added in the range in 2010 followed by Ammonia Evaporators and Condensers added in the product range in 2012 with the initiation of stainless steel pipe production. 2014 and 2015 were the years of transition of energy efficient, user friendly, high performing new generation Evaporators and Condensers.

FRITERM is at the disposal of the sector with its two manufacturing plants on an indoor area of 19,000 m2 in Tuzla - Istanbul with 246 competent staff and modern machinery park.

FRITERM will reinforce its role as a leading supplier in the Air Conditioning and Energy Sector with its New Facility at Makine Ihtisas Organized Industrial Zone built on an indoor area of 36,000 m2 over 60-decares of land, which will start to operate at the second quarter of 2016.

The Manufacturing and the Office Buildings have been designed to use natural resources such as solar and wind showing utmost attention to protect the environment to obtain the BREEAM certificate for the Manufacturing Building and the LEED Certificate for the Office Building.

Following the commissioning of the facility, the FRITERM ACADEMY, R&D and Lab in the Tuzla Facility activities will grow exponentially and FRITERM’s contribution to the science of Heat Transfer will increase.